Bush DHB7VTDW 7KG Vented Tumble Dryer - White

If the clothes aren’t drying, check the following:

• Clean the lint filter by removing it and removing any dust and debris.
• Remove the condenser drawer, wash thoroughly, allow to dry and refit into the appliance.
• Check that the appliance has not been overloaded. If the load is too big, then the clothes won't move freely to dry.
• If clothes are soaking wet, try wringing water out to remove excess moisture before putting in the appliance.

If the issue is still not resolved, please get in touch with the support team using the contact details on this page.

If the drum isn’t moving, try the following:

• Check that the appliance is plugged in and switched on. If necessary, try an alternative mains plug socket.
• Clean the lint filter by removing it and removing any dust and debris.
• Empty the water tank and clean it thoroughly.
• Remove the condenser drawer, wash thoroughly, allow to dry and refit into the appliance.
• Check that a time delay has not been set on the appliance. Remove the time delay and try again.
• Check the load is the correct size. If the load is too big then the drum may not spin.

If the issue is still not resolved, please get in touch with the support team by using the contact details on this page.

If clothes are coming out damaged, check the following:

• Ensure the drum is not being overloaded.
• Ensure the appliance is on the correct programme.

If the issue is still not resolved, please get in touch with the support team using the contact details on this page.

If the appliance is tripping the electrics, check the following:

• Check the plug is inserted fully.
• Check and/or change the fuse.
• Check the lint filter by removing it and removing any dust and debris.

If the issue is still not resolved, please get in touch with the support team by using the contact details on this page.

If the cycle won’t start, try the following:

• Check that the appliance is plugged in and switched on. If necessary, try an alternative mains plug socket.
• Clean the lint filter by removing it and removing any dust and debris.
• Empty the water tank and clean it thoroughly.
• Remove the condenser drawer, wash thoroughly, allow to dry and refit into the appliance.
• Check that a time delay has not been set on the appliance. Remove the time delay and try again.

If the issue is still not resolved, please get in touch with the support team by using the contact details on this page.

If the programme is stopping after a few minutes, check the following:

• Check the lint filter by removing it and removing any dust and debris.
• Empty the water tank and clean it thoroughly.
• Remove the condenser drawer, wash thoroughly, allow to dry and refit into the appliance.
• Check that the appliance has not been overloaded. If the load size is too big, then the clothes won't move freely and the cycle may stop.
• Ensure the unit is plugged in correctly.

If the issue is still not resolved, please get in touch with the support team by using the contact details on this page.

If the appliance is going over set times on drying clothes, check the following:

• Check the lint filter by removing it and removing any dust and debris.
• Empty the water tank and clean it thoroughly.
• Remove the condenser drawer, wash thoroughly, allow to dry and refit into the appliance.
• Check that the correct load size has been used for the programme selected. If overloaded, it may take longer to dry completely.
• Try not to put the clothes in overly wet as they will take longer to dry.

If the issue is still not resolved, please get in touch with the support team using the contact details on this page.

This is to stop the clothes from creasing. The drum will occasionally turn until the appliance has been either switched off or the door has been opened.

• Ensure the lint filter is clean by removing, cleaning, drying and refitting. 
• Clean the air intake shroud from any lint or debris, dry and then refit. 
• Check that the appliance is on a stable, level surface with sufficient clearance around it. 
• Ensure that the vents are not trapped or blocked which could create excessive noise. 

• Ensure the door is closed correctly with nothing obstructing it. 
• Ensure the lint filter is clean by removing, cleaning, drying and refitting. 
• Wipe the humidity sensors inside the drum to remove debris (if available on your model). 
• Clean the air intake shroud from any lint or debris, dry and then refit. 
• Perform a power reset by unplugging the appliance from power, holding down the Start/Pause button for 10 seconds, waiting 30 seconds and trying the appliance again.     
• Check that the load size is not too big or too small for the programme selected as it may overload or underload. 

If the cycle won’t start, try the following: 

• Ensure the door is closed correctly with nothing obstructing it. 
• Ensure a time delay has not been set. 
• Check that power is going to the appliance. 
• Ensure the lint filter is clean by removing, cleaning, drying and refitting. 
• Wipe the humidity sensors inside the drum to remove debris (if available on your model). 
• Clean the air intake shroud from any lint or debris, dry and then refit. 
• Perform a power reset by unplugging the appliance from power, holding down the Start/Pause button for 10 seconds, waiting 30 seconds and trying the appliance again.